- 您现在的位置：买卖IC网 > Sheet目录1210 > DK-114N-3 (Luminus Devices Inc)KIT DEV PHLATLIGHT CBT/PT LED
PhlatLight ? DK-114N Series Development Kit Manual
age types, a cable is soldered to the board.
The 12” cable assembly, which includes the interface board
to driver board cables as well as the interface board to fan
cable connects as shown in Figures 13 and 14. The 12” ca-
ble assembly, as shown in figure 13, connects the control
board to a power supply. This connection is shown in figure
15.
Important Note: In almost all cases, the connectors will only
insert in one direction. Care must be taken not to force any of
the connections as this may damage the connectors. In the
case that the connector can be connected improperly, the con-
nector and mating cable are clearly marked with either color
coding or lettering. If powered with improper connections,
Figure 9: PhlatLight device placed on top of thermal inter-
damage can be caused to the LEDs and circuit boards.
face material
4. Insert screws in the holes of the coreboard and tighten. To
ensure equal pressure is exerted by all screws, alternate
tightening each screw until the board is securely fastened
(Figure 10). The device is now mounted and ready for elec-
trical connections.
Figure 11: CBT-54 LED to driver board cable interface
Figure 10: Fully mounted PhlatLight device
Electrical Connections
The following sections assume that the user has all of the
equipment listed in Table 1.
1. Prepare the power supply and ensure the power supply be-
ing used is capable of providing enough power to the devic-
es. A single channel at full power will draw up to ~80W at
12V and 6.5A. If using a variable power supply like the
Lambda ZUP2020, preset the voltage to 12V and set the
current to the maximum. Power off the supply until all con-
nections are established and the board settings are ready.
2. Attach all of the wiring included in the kit. The short, 3”
Figure 12: CBT-54 LED to driver board cable interface
cable connects the LED (C21 package types only) to the
driver board as shown in Figures 11 and 12. For C11 pack-
? 2009 Luminus Devices, Inc. - All Rights Reserved
Page 5
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
DK-136M-3
KIT DEV PHLATLIGHT CBT/PT LED
DK-409N-1
KIT DEV PHLATLIGHT CBM360 LED
DK-414N-4
KIT DEV PHLATLIGHT CBM380 LED
DK-PS21765
KIT DEV INTERFACE IPM MINIDIP
DK-PS21965
KIT DEV INTERFACE IPM MINIDIP
DK-RV-1.8-TRK-33
EVAL KIT SQUIGGLE MOTOR + SENSOR
DK-SI-4S100G2N
KIT DEV STRATIX IV TRANSCEIVER
DLP-2232H
MODULE USB ADAPTER FOR FT2232H
相关代理商/技术参数
DK115199
制造商:TE Connectivity 功能描述:
DK115201
制造商:TE Connectivity 功能描述:
DK115202
制造商:TE Connectivity 功能描述:
DK116399
制造商:TE Connectivity 功能描述:
DK116664
制造商:TE Connectivity 功能描述:
DK117439
制造商:TE Connectivity 功能描述:
DK11XEA100K86RAH01
功能描述:CAP CER 10PF 250V SL NONSTND SMD 制造商:murata electronics north america 系列:DK1 包装:剪切带（CT） 零件状态:在售 电容:10pF 容差:±10% 电压 - 额定:250V 温度系数:SL 工作温度:-40°C ~ 125°C 特性:- 等级:X1，Y1 应用:安全 故障率:- 安装类型:表面贴装，MLCC 封装/外壳:非标准型 SMD 大小/尺寸:0.315" 长 x 0.236" 宽（8.00mm x 6.00mm） 高度 - 安装（最大值）:- 厚度（最大值）:0.098"（2.50mm） 引线间距:- 引线形式:鸥翼型 标准包装:1
DK11XEA100K86RBH01
功能描述:CAP CER 10PF 300V SL NONSTND SMD 制造商:murata electronics north america 系列:DK1 包装:剪切带（CT） 零件状态:在售 电容:10pF 容差:±10% 电压 - 额定:300V 温度系数:SL 工作温度:-40°C ~ 125°C 特性:- 等级:X1，Y1 应用:安全 故障率:- 安装类型:表面贴装，MLCC 封装/外壳:非标准型 SMD 大小/尺寸:0.315" 长 x 0.236" 宽（8.00mm x 6.00mm） 高度 - 安装（最大值）:- 厚度（最大值）:0.098"（2.50mm） 引线间距:- 引线形式:鸥翼型 标准包装:1